Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
2.1. Maintenance
2.1.1. Check of level of engine oil
2.1.2. Replacement of engine oil
2.1.3. Choice of the oil filter
2.1.4. Replacement of the oil filter
2.1.5. Check of tightness of system of cooling
2.1.6. Check of valves of a cover of a radiator
2.1.7. Check of concentration of antifreeze
2.1.8. Compression check
2.1.9. Adjustment of a tension of a belt of a drive of GRM
2.1.10. Drive of hinged units
2.1.11. Natyazhitel of a belt of a drive of hinged units
2.1.12. Adjustment of a belt of a drive of hinged units
2.1.13. Adjustment of a belt of a drive of the generator
2.2. Mechanical part (engine of 1,6 l)
2.3. Mechanical part (engine of 1.8 l)
2.4. Cooling system
2.5. Greasing system
2.6. Power supply system
2.7. Control system, fuel system and system of decrease in toxicity
2.8. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 




2-1-11-natyazhitel-remnya-privoda-navesnykh-agregatov.html

2.1.11. Natyazhitel of a belt of a drive of hinged units

Static check
Natyazhitel of a belt of a drive of hinged units can be checked statically, operating how it is described below.
1. Disconnect a belt of a drive of hinged units in a zone of a natyazhitel of a belt.
2. Using the special tool, move a natyazhitel of a belt from its free situation at full capacity the piston and back to free situation to make sure that there is no jamming and a prikhvatyvaniye, and make sure that the spring of a natyazhitel of a belt is in a tension.
3. Turn a pulley of a natyazhitel of a belt of a drive of hinged units and check it on existence of damages and freedom of rotation and correctness of adjustment. If necessary establish a new natyazhitel.
4. Examine a zone, surrounding a natyazhitel of a belt of a drive of hinged units on availability of greasing or other pollution. Before installation of a new natyazhitel eliminate all leakages. If the natyazhitel of a belt is polluted, do not try to clear it since the mechanism of damping located inside can be damaged. If necessary establish a new natyazhitel.
5. If the natyazhitel of a belt of a drive of hinged units satisfies to aforementioned criteria, pass to dynamic check. If the natyazhitel of a belt of a drive of hinged units does not satisfy to aforementioned criteria, establish a new natyazhitel.

Dynamic check
Natyazhitel of a belt of a drive of hinged units can be checked dynamically, operating in given below sequence.
At the working engine watch moving of a natyazhitel of a belt. Natyazhitel should move to (react) at sharp acceleration of the engine or at the А/С coupling tsiklirovaniye. If moving of a natyazhitel has no constant character without acceleration of the engine or the А/С coupling tsiklirovaniye, it is possible that the pulley or a shaft is deformed or has a deviation from a standard form, or the mechanism of damping located in a natyazhitel is damaged. Excessive running start of a belt of a drive of hinged units (unequal depth of flutes in a belt of a drive of accessories) can cause excessive moving of a natyazhitel of a belt. Check a problem condition, having established a new belt of a drive of hinged units.
«previous page
2.1.10. Drive of hinged units		 following page»
2.1.12. Adjustment of a belt of a drive of hinged units