8.2.6. Removal and windscreen installation

Remove facings of forward racks a body.

Remove an internal rear-view mirror.

Remove screen wiper levers.

Remove a sealant and a cover of a niche of the air intake.

Fig. 8.27. Removal of a sealant of a windscreen

Remove a windscreen sealant (fig. 8.27).

Fig. 8.28. Removal of the remains of glue

Cut off the glue remains by means of the adaptation 09861-31100 (fig. 8.28).

Fig. 8.29. Drawing of labels on glass and an aperture

In case of a reuse of glass put adjusting labels on glass and I will eat (fig. 8.29).

Remove a windscreen.

Fig. 8.30. Alignment of a glutinous layer

By means of a cutting torch or the adaptation 09861-31200 exactly cut off the glue roller till the thickness about 2 mm from a surface of gluing of glass on all perimeter of a flange of an aperture (fig. 8.30).

ATTENTION Do not cut off the glue roller till the thickness less specified, and accept precautionary measures not to damage a paint and varnish covering of a body a cutting torch. At damage restore a layer, having put finishing paint.

Clear a flange of an aperture of a windscreen a sponge impregnated with alcohol or means for removal of mastics and degreasing.

Fig. 8.31. Installation of pro-rates

Establish pro-rates in a windscreen aperture (fig. 8.31).

Fig. 8.32. Drawing of labels on glass and a body

Establish a new windscreen in an aperture and with a soft pencil put labels on glass and a body in four places, as is shown in drawing 8.32.

Fig. 8.33. Installation of an overlay for a windscreen

Establish an overlay of a windscreen, watching that there were no gaps (fig. 8.33).

Fig. 8.34. Scheme of a sticker of a rubber insert

On an internal surface of glass on all perimeter of an edge paste a rubber insert, the employee for glue deduction at installation flew down (fig. 8.34).

Fig. 8.35. Place of drawing of glutinous soil

Apply a thin film glutinous soil for glasses on an external surface of a rubber insert (8.35).

NOTE Do not touch glass since it can worsen quality of gluing together and to become the leakage reason after windscreen installation. Do not put on glass glutinous soil for body details. Do not allow hit on the put glutinous sheet of water, a dust and abrasive particles.

Fig. 8.36. The scheme of drawing of glutinous soil on the bottom edge of glass

Put glutinous soil on the bottom edge of glass, as is shown in drawing 8.36.

Fig. 8.37. The scheme of drawing of hermetic on glass edges

Put hermetic on glass edges on all perimeter (fig. 8.37).

NOTE Put a glue layer no more than through 5 mines after drawing of glutinous soil.

Apply a thin film glutinous soil for body details on left on a flange of an aperture of glass a hermetic layer. After drawing of glutinous soil establish glass not later than in 5 minutes.

By means of suckers 09861-31400 impose a windscreen on an aperture, combining the put labels and press glass to a hermetic layer.

Remove surplus of glue with a shpatel or erase it a gauze. Fill with glue all emptiness on glass perimeter.

Be convinced of tightness of a windscreen for what water it with a stream of cold water, watching that a strong stream not to damage a fresh glutinous layer. Water so that water flew down on glass edges.

At detection of leakages dry a place of a leakage and put hermetic.

Establish earlier removed details.

NOTE Within the first hour after installation do not allow water hit on a windscreen. Do not make trips on the car within the first four hours after windscreen installation. In need of a trip during the first 8 чдвигайтесь with small speed. Do not slam with force of a door. Do not allow impact on a body of big braiding loadings which arise at congresses from a carriageway or departures on it, or during movement on rough roads.