3.4.2. A shaft of a drive of a forward wheel (the CV JOINT with the jack of length (DOJ) and the CV JOINT «Birfilda BJ»)

Fig. 3.120. A shaft of a drive of a forward wheel (the CV joint with the jack of length (DOJ) and the Birfilda CV JOINT (BJ))

ATTENTION Do not assort the external CV JOINT «Birfilda of BJ». Special konsistentny greasing is applied to greasing of CV JOINTS of a shaft of a drive of a wheel. Do not mix old and new greasing, and also different types of konsistentny greasings. After removal replace collars of protective covers of the CV JOINT new.

Fig. 3.121. Removal of a collar of fastening of a protective cover

Remove collars of fastening of a protective cover of the internal CV JOINT and remove a protective cover from an external holder of the internal CV JOINT (fig. 3.121).

ATTENTION Be careful, do not damage a protective cover at removal.

Fig. 3.122. Removal of a lock ring

By means of a flat screw-driver take a big lock ring from an external holder of the CV JOINT (fig. 3.122).

Extend a shaft of a drive of a wheel from an external holder of the CV JOINT.

Fig. 3.123. Removal of a small lock ring

Remove a small lock ring and take an internal holder of the CV JOINT assembled with a separator and balls (fig. 3.123).

Clear an internal holder of the CV JOINT assembled with a separator and balls, without assorting knot.

Remove collars of a protective cover of the external CV JOINT and a protective cover from the case of the external CV JOINT.

Fig. 3.124. Installation of a sticky safety tape

ATTENTION If repeated installation of a protective cover of the CV JOINT is supposed, wrap up (plastic) insulating tape a shlitsevy part of a shaft not to damage a cover (fig. 3.124).

Check an external holder of the internal CV JOINT, an internal holder, a separator and balls on absence of damages or a rust.

Check a shlitsevy part of a shaft of a drive of a wheel on lack of traces of the increased wear.

Be convinced of lack of the water, extraneous particles, dirt or rusts in a protective cover of the external CV JOINT.

Fig. 3.125. Cleaning of the external CV JOINT

ATTENTION If repeated installation of the external CV JOINT assembled is supposed, do not delete from it greasing. Check lack of extraneous particles in CV JOINT greasing. If necessary completely clear the external CV JOINT assembled of pollution and greasing, then put in the CV JOINT new konsistentny greasing (fig. 3.125).

Wrap up (plastic) insulating tape a shlitsevy part of a shaft of a drive of a wheel from the internal CV JOINT not to damage a cover.

Put greasing on a shaft of a drive of a wheel and establish protective covers of CV JOINTS.

External CV JOINT (BJ): CENTOPLEX 278M/136K.

Internal CV JOINT (DOJ): AMBLYGON THAT 10/2A.

Fig. 3.126. Scheme of fixing of a dynamic damper

For installation of a dynamic damper, holding the external CV JOINT and a shaft of a drive of a wheel so that they were on a straight line, fix a dynamic damper a collar in the places specified in drawing 3.126.

Fig. 3.127. Separator installation

Put special konsistentny greasing on an internal holder and the CV JOINT separator. Establish a separator so that the distance between it and an internal holder corresponded specified in drawing 3.127.

NOTE Use special greasing from ремкомплекта.

Put special konsistentny greasing on a separator of the internal CV JOINT and establish balls in a separator.

Fig. 3.128. Installation of the internal CV JOINT

Arrange the party (And) the internal CV JOINT, as is shown in drawing 3.128.

Establish an internal holder of the CV JOINT on a shaft of a drive of a wheel and fix a lock ring.

Put special konsistentny greasing in an external holder of the internal CV JOINT, establish it on a shaft of a drive of a wheel and fix a lock ring.

Fill with special konsistentny greasing a protective cover of the internal CV JOINT and establish it into place.

Fix a protective cover of the internal CV JOINT collars.

Add special konsistentny greasing in the case of the external CV JOINT in quantity which corresponds to amount of the greasing removed at check.

Establish a protective cover of the external CV JOINT.

Fix a protective cover of the external CV JOINT collars.

Fig. 3.129. Installation of collars of protective covers

Establish collars of protective covers of external CV JOINTS at the corresponding distance from each other (to provide necessary volume of air in a cover) and then reliably tighten collars (fig. 3.129).